ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 1 d escription the ACE7215C is a high - efficiency monolithic synchronous buck regulator using a constant frequency, current mode architecture. the device is available in an adjustable version. supply current with no load is 40ua and drops to <1ua in shutdown. the 2.5v to 6v input voltage range makes the ACE7215C ideally suited for single li - ion battery powered applications. 100% duty cycle provides low dropout operation, extending battery life in portable systems. pwm/pfm mode operation provides very low outpu t ripple voltage for noise sensitive applications. switching frequency is internally set at 1.5mhz, allowing the use of small surface mount inductors and capacitors. low output voltages are easily supported with the 0.6v feedback reference voltage. the ace 7215c is available in sot23 - 5 and dfn2*2 - 6l package. features ? high efficiency: up to 96% ? 2.5v to 6v input voltage range ? 1.5mhz constant frequency operation ? no schottky diode required ? low dropout operation:100% duty cycle ? pfm mode for high efficiency in li ght load ? over temperature protected ? low quiescent current: 40a ? short circuit protection ? inrush current limit and soft start ? available in sot23 - 5 and dfn2*2 - 6l application ? cellular and smart phones ? wireless and dsl modems ? pdas ? portable instruments ? digital still and video cameras ? pc cards
ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 2 absolute maximum rating s p arameter value max input voltage 7 v max voltage all pins 7 v max operating junction temperature(tj) 125 ambient temperature(ta) - 40 ~ 85 maximum power dissipation sot23 - 5 400m w dfn2*2 - 6l 600mw storage temperature(ts) - 40 ~ 50 lead temperature & time 260 , 10s note: exceed these limits to damage to the device. exposure to absolute maximum rating conditions may affect device reliability. packaging type sot23 - 5 dfn2*2 - 6l pin no description description sot23 - 5 dfn2*2 - 6l 1 2 en chip enable pin. drive en above 1.5v to turn on the part. drive en below 0.3v to turn it off. do not leave en floating. 2 1/5/7 gnd ground 3 4 sw power switch output. it is the switch node connection to inductor. this pin connects to the drains of the internal p - ch and n - ch mosfet switches. 4 3 vin supply voltage. must be closely decoupled to gnd with a 10f or greater ceramic capacitor. 5 6 fb output voltage feedback pin. an internal res istive divider divides the output voltage down for comparison to the internal reference voltage. ordering information ACE7215C xx + h pb - free bn
ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 3 t ypical a pplication b lock d iagram
ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 4 electrical characteristics symbol para meter conditions min typ m ax unit vin input voltage range 2.5 6 v vref feedback voltage 0.588 0.6 0.612 v iq quiescent current fb= 90%, vin=5.0v, iload=0ma 150 300 ua fb= 05%, vin=5.0v, iload=0ma 40 70 v en = 0v, vin=4.2v 0.1 1.0 lnreg line regulation vin=2.5v to 6v 0.1 0.2 %/v ldreg load regulation 0.5 % fsoc switching frequency 1.5 mhz rdsonp pmos rdson i sw =100ma 300 mohm rdsonn nmos rdson i sw = - 100ma 200 mohm ilimit peak current limit vin=5v, vout=3.3v 1.5 a inoload* vi n=5v, vout=3.3v, iout=0 43 ua iswlk sw leakage current v en =0v,vin=vsw=5v 1 ua ienlk en leakage current 1 ua vh_en en input high voltage 1.04 v vl_en en input low voltage 0.98 v note: *when dutycycle >90%, inoload will increase. e.g. vin=3 .5v/vout=3.3v, inoload=800ua.
ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 5 detailed description the ACE7215C uses a constant frequency, current mode step - down architecture. both the main (p - channel mosfet) and synchronous (n - channel mosfet) switches are internal. during normal operation, the inter nal top power mosfet is turned on each cycle when the oscillator sets the rs latch, and turned off when the current comparator, icomp, resets the rs latch. the peak inductor current at which icomp resets the rs latch, is controlled by the output of error a mplifier ea. when the load current increases, it causes a slight decrease in the feedback voltage, fb, relative to the 0.6v reference, which in turn, causes the ea amplifiers output voltage to increase until the average inductor current matches the new lo ad current. while the top mosfet is off, the bottom mosfet is turned on until either the inductor c urrent starts to reverse, as indicated by the current reversal comparator ircmp, or the beginning of the next clock cycle. applications information setting the output voltage in the adjustable version, the output voltage is set by a resistive divider according to the following formula: the external resistive divider is connected to the output, allowing r emote voltage sensing as shown in on page 1 . induct or selection for most designs, the ACE7215C operates with inductors of 1h to 4.7h. low inductance values are physically smaller but require faster switching, which results in some efficiency loss. the inductor value can be derived from the following equa tion: where ? i l is inductor ripple current. large value inductors result in lower ripple current and small value inductors result in high ripple current. for optimum voltage - positioning load transients, choose an inductor with dc series resistance in the 50m? to 150m? range.
ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 6 input capacitor selection higher values, lower cost ceramic capacitors are now becoming available in smaller case sizes. their high ripple current, high voltage rating and low esr make them ideal for switching regulator applica tions. because the ACE7215C s control loop does not depend on the output capacitors esr for stable operation, ceramic capacitors can be used freely to achieve very low output ripple and small circuit size. however, care must be taken when ceramic capacito rs are used at the input and the output. when a ceramic capacitor is used at the input and the power is supplied by a wall adapter through long wires, a load step at the output can induce ringing at the input, vin. at best, this ringing can couple to the o utput and be mistaken as loop instability. at worst, a sudden inrush of current through the long wires can potentially cause a voltage spike at vin, large enough to damage the part. when choosing the input a nd output ceramic capacitors, choose the x5r or x 7r dielectric formulations. these dielectrics have the best temperature and voltage characteristics of all the ceramics for a given value and size. pc board layout checklist when laying out the printed circuit board, the following checking should be used to ensure proper operation of the ACE7215C . check the following in your layout: 1. the power traces, consisting of the gnd trace, the sw trace and the vin trace should be kept short, direct and wide. 2. does the (+) plates of cin connect to vin as closely as po ssible? this capacitor provides the ac current to the internal power mosfets. 3. keep the switching node, sw, away from the sensitive vout node. 4. keep the ( - ) plates of cin and cout as close as possible
ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 7 e lectrical p erformance tested under ta=25 , unless otherwise specified
ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 8 packing information sot23 - 5 unit: mm
ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 9 packing information dfn2*2 - 6l
ace7 215 c 1.5a 1.5mhz synchronous buck converter ver 1.1 10 notes ace does not assume any r esponsibility for use as critical components in life support devices or systems without the express written approval of the president and general counsel of ace electronics co., ltd. as sued herein: 1. life support devices or systems are devices or systems wh ich, (a) are intended for surgical implant into the body, or (b) support or sustain life, and shoes failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significan t injury to the user. 2. a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ace technology co., ltd. http://www.ace - ele.com/
|
